GBodyCentral.com  
  #91  
Old 03-12-2017, 02:49 PM
Poltergeist's Avatar
Poltergeist Poltergeist is offline
Just a ghost in the machine
 
Join Date: Aug 2010
Location: Ontario, Calif.
Posts: 2,729

Default

Nice info.
__________________
1982 El Camino (Original owner)
LT1 from a '95 Impala
A bunch of other stuff check out my Garage
Reply With Quote
  #92  
Old 06-28-2017, 10:45 AM
malibudave malibudave is offline
Gear Head
 
Join Date: Aug 2010
Location: Houston, TX
Posts: 42
Default

I pulled this information from the CPP website. I include this information on this thread because, during a manual brake conversion, the differential valve in the proportioning/combination valve may be triggered and cause only one side of the system to work resulting in poor braking performance.

The differential valve is built into most GM prop valves. It is for safety. If one side, front or rear, of the brake system looses pressure, the differential valve is triggered blocking off the low pressure side of the brake system so that the master cylinder can still provide pressure to the other side of the brake system. This ensures that there is some for of braking as a way to stop the vehicle. If a differential valve was not part of the braking system, and there is a loss of pressure in one side of the system, the master cylinder would not be able to build pressure. This would result in NO brakes.

Combination/Proportioning Valve Test

Use a test light by attaching a clip to a positive contact on the vehicle and touch the point of the tester to the electrical connection of the combination valve. If the the light does NOT come on, the valve system is operating correctly and no further testing is required.

If the light does come on, this indicates that the pressure differential valve is stuck in the front or rear position.

Bleed the brake system to determine if the front or rear lines are blocked off. Set up one front wheel and one rear wheel for bleeding at the same time. Crack both bleeder screws and gently pump the pedal a few times.

The blocked side will trickle fluid out when the bleeder screw is cracked and the pedal pressed. An unblocked line will squirt fluid out the bleeder.
The lines that are clear must be left open and the blocked lines should have the bleeder screws tight to cause pressure to build up on that side. Be sure to use the standard bleeding procedures to prevent air from entering the system.

Slowly press the pedal with steady pressure a number of times until the light goes out; this will center the differential valve. You may also hear a pop come from the proportioning valve. This is the metering valve returning to its equalized position. When the light goes out, close the bleeder screw. (See fig. below)


__________________
David Schultz
MalibuDave
www.manualbrakes.com
www.facebook.com/manualbrakescom-576443512373024/
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Aluminum G-body Manual Brake Adapter Plate malibudave Garage Sale 3 02-19-2014 06:01 PM
2002 LS1 Trans Am brake on a 87 MC SS Gbody_Rida Brakes 5 04-18-2012 02:36 PM
Flynbye Front C5 conversion bracket question CruizinKev Brakes 1 02-08-2012 12:21 PM
Manual to power windows! Bigjoenvegas Appearance & Detailing 1 11-16-2011 06:32 AM
Auto to Manual. . . 87 Elky SS Transmission / Rear Differential 8 10-23-2010 12:42 AM


All times are GMT -7. The time now is 07:43 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
vB.Sponsors